Q1: Eng thil nge hlawhchhamna tlangpuiheat exchanger te pawh a awm bawkoperation neih laiin?
Industrial system-a heat transfer device pawimawh tak a nih angin, heat exchanger-te hian hun rei tak-a an thawh hnuah fluid property, operating conditions, leh maintenance practices avang hian performance degradation emaw equipment chhiatna emaw an tawk thei a ni. Hlawhchhamna tam ber chu:
1. Heat Transfer Efficiency tihhniam
A chhan: 1.1.
Hun kal zelah heat transfer surface-ah bawlhhlawh, scale leh deposit te a awm khawm thei a, hei hian thermal resistance a tipung a, heat transfer efficiency a ti tlem thei bawk.
Fluid flow rate tling lo, operating temperature inthlak danglam, emaw hmanrua thlan dik loh te hian heat transfer performance tak tak chu designed capacity aia hniam a thlen thei bawk.
Siamthat dan: 1.1.
Plate, tube emaw heat transfer surface atanga deposit awmte paih chhuah nan tihfai fo thin ang che.
Fluid flow rates leh operating parameters te enfiah la, design mamawh ang zela system condition te pawh siamrem rawh.
A tul chuan heat transfer capacity chu chhut nawn leh la, equipment design chu optimize la, heat transfer area tihpun rawh.
Q2: Engvangin nge tihheat exchanger te pawh a awm bawkhnamchhuak? Engtin nge leakage hi siamthat theih ang?
1. Sealing Components tar emaw, a chhiat emaw
A chhan: 1.1.
Plate heat exchanger-ah chuan gasket te hi temperature sang tak, pressure sang tak leh chemical fluid-ah hun rei tak an awm a, chu chuan tar, hardening, elasticity hloh emaw a thlen thei a ni.
Gasket dah dik loh emaw, tightening dimension dik lo emaw chuan sealing a chhiat phah thei bawk.
Siamthat dan: 1.1.
Gasket chhia emaw, upa tawh emaw chu hnathawhna temperature leh chemical condition nena inmil thar hmangin thlak thin ang che.
Heat exchanger plate te tightening dimension enfiah la, siamtute mamawh angin dah leh rawh.
2. Plate leh Tube-a Corrosion emaw Perforation emaw
A chhan: 1.1.
Fluid chhunga thil chhe thei, chloride ion emaw acidic chemical emaw te hian thir thilte chu zawi zawiin a tichhia thei a ni.
Hun rei tak-corrosion hian plate emaw tube emaw a ti thin a, a tawpah chuan crack emaw leakage emaw a thlen thei bawk.
Siamthat dan: 1.1.
Component chhia te chu thlak nghal rawh.
Fluid characteristic angin corrosion-resistant materials thlang la, stainless steel, titanium, emaw special alloy emaw ang chi te.
System chhunga thil chhe thei awmte tihtlem nan tui quality control tihchangtlun.
Q3: Engvangin nge tihheat exchanger te pawh a awm bawkblockage a tawk em? Engtin nge a chinfel theih ang?
1. Flow Channel tihkhawtlai a ni
A chhan: 1.1.
Fluid-a bawlhhlawh, particle emaw, suspended solid emaw awmna chu hun kal zelah flow channel chhungah a pung khawm thei a ni.
Plate heat exchanger te hi an flow passage te tak te avang hian blockage an sensitive zawk a ni.
Siamthat dan: 1.1.
Shutdown hnuah mechanical cleaning emaw chemical cleaning emaw tih tur a ni.
Inlet-ah hian filter emaw separator emaw dah la, chu chuan bawlhhlawh a luh loh nan.
Filtration system te enfiah leh tifai fo thin ang che.
2. Scaling lama harsatna awm thei
A chhan: 1.1.
Tui chhunga calcium leh magnesium ion te hian temperature sang-temperature condition hnuaiah scale deposit an siam thei a ni.
Oil product leh high-viscosity fluid te hian heat transfer performance tihhniam thei deposit a siam thei a ni.
Siamthat dan: 1.1.
Deposit chi hrang hrang a zirin tihfai dan tur dik tak thlang la, chu chu acid tihfai, alkaline tihfai, emaw high-pressure water flushing te hi a ni.
Scale formation rate tihhniam nan operating temperature optimize.
Tui circulating quality tihchangtlun nan tui thianghlim system hmang rawh.
Q5:Engtin ngeheat exchanger a nivibration leh abnormal noise te chu chinfel a ni em?
1. Fluid Velocity tam lutuk
A chhan: 1.1.
Fluid velocity tam lutuk hian turbulence nasa tak a siam thei a, hnathawh laiin vibration leh noise pangngai lo a siam thei a ni.
Flow velocity sang hian heat transfer tube emaw plate emaw-ah mechanical stress a tipung thei a, chu chuan hun rei tak-a hnathawh chhungin fatigue damage a thlen thei a ni.
Siamthat dan: 1.1.
Fluid velocity tihhniam nan inlet flow rate chu siamrem la, design range rawt chhungah dah rawh.
Flow condition nghet tak neih theih nan pump hnathawh leh control valve te tihchangtlun.
Heat exchanger design chu hnathawhna atana mamawh tak tak nen a inmil em tih enfiah rawh.
2. Boruak khawlkhawm emaw Tui Hammer Effect emaw
A chhan: 1.1.
Heat exchanger system chhunga boruak tang chuan fluid circulation pangngai a titawp thei a, hnathawh dan mumal lo tak a siam thei bawk.
Valve rang taka hawn emaw khar emaw hian pressure a tidanglam nghal thei a, chu chuan water hammer leh mechanical vibration a thlen thei a ni.
Siamthat dan: 1.1.
Venting procedure dik tak hmangin system atanga boruak tang chu paih chhuak rawh.
Valve hman dan siam that leh pressure inthlak danglam nghal loh tur.
Air release valve dah emaw, a tul chuan system piping design siam that emaw.
3. Components loose emaw Installation dik lo emaw
A chhan: 1.1.
Bolt, support emaw connection parts lo sei te hian hmanrua hman laiin vibration pangngai lo a siam thei.
Installation alignment dik lo emaw, support tling lo emaw chuan mechanical stress a tipung thei a, noise a siam thei bawk.
Hun rei tak-vibration hian fastener te chu zawi zawiin a tizau thei a, equipment stability a nghawng thei bawk.
Siamthat dan: 1.1.
Bolt, support, leh connection component zawng zawng chu siamtu specification angin enfiah la, khauh rawh.
Installation alignment enfiah la, heat exchanger chu a support tha em tih enfiah rawh.
Structural part chhia te thlak leh a tul hunah support system tichak bawk ang che.
Q6: Engvangin nge heat exchanger temperature danglamna hi a tawk loh?
1. Fluid lum leh vawt inkara Temperature danglamna tihhniam
A chhan: 1.1.
Fluid lum leh vawt inlet temperature chu design condition nen a danglam chuan heat transfer capacity a tlahniam ang.
System load inthlak danglamna hian outlet temperature a nghawng thei bawk.
Siamthat dan: 1.1.
Heat source leh cooling source temperature te hian design mamawh a tlin leh tlin loh enfiah thin ang che.
Heat transfer atana driving force tihpun nan operating condition siamrem rawh.
2. Heat Transfer Area tling lo
A chhan: 1.1.
Production capacity a san emaw, process condition a inthlak emaw chuan original heat transfer area chuan a mamawh a tlin tawh lo mai thei.
Siamthat dan: 1.1.
Heat transfer area tihpun a ni.
Thil hmanrua chu heat exchanger type tha zawk hmangin thlak leh rawh.
Q7: Engtin nge heat exchanger chhiatna hi ven theih ang?
1. Regular Maintenance Programme siam
Operating parameters te enfiah fo thin la, temperature, pressure, flow rate, leh pressure drop inthlak danglamna te pawh a tel.
Fouling tam lutuk ven nan operating condition a zirin cleaning schedule mumal tak siam rawh.
2. Operation Monitoring chhunzawm zel tur
Inlet leh outlet temperature leh pressure inthlak dan enfiahin performance degradation hriat theih a ni.
Harsatna tenau te chu hlawhchhamna lian takah a chan loh nan operating data pangngai lo chhui nghal rawh.
3. Thil hman tur dik tak thlang rawh
Fluid characteristic, temperature leh pressure condition atanga thlirin material tha tak tak thlang rawh.
Corrosive environment tan chuan hmanrua rintlak leh service life tihchangtlun nan corrosion-resistant materials hmang ang che.
Heat exchanger unit chungchang hriat belh duh emaw, lei duh emaw i nih chuan 9988xiaoshuai@gmail.com ah email thawn la, message i hmuh hnuah a hun takah kan chhang ang che!
Professional team te an ni
Kan company hian technical personnel te chu a bulpui ber hmangin after-sales service team quality sang tak-a thuam a ni a, a hmangtute hnen atanga service information notification a dawn hunah a hun taka feedback a pe ang.
Darkar 7x24 chhung a rawn thawn thei
Kan company hian kan thil zawrh te chu a thlawnin technical support a pe a, a kaihhnawih mipa te tan technical training a buatsaih bawk.
